*If you have any issues with printing or assembly, feel free to message me, and I'll do my best to assist you 😉.

https://linktr.ee/leoteapproach

/////LINKS FOR THE HARDWARE USED IN ALL MY PROJECTS * affiliate links

INSERTS M3 x 4mm (L) x 5mm (D): https://amzn.to/3EovAVw

HEX SOCKET CAP M3 6mm-30mm (STAINLESS): https://amzn.to/4imGAQW

HEX SOCKET CAP M3 6-20mm (BLACK): https://amzn.to/3R7wjx4

FLAT HEAD SOCKET CAP M3 4mm-12mm (STAINLESS): https://amzn.to/3G3Z1wr

FLAT HEAD SOCKET CAP M3 8mm-25mm (BLACK): https://amzn.to/43JeThP

HONEYCOMB WALLS FOR CREALITY K1 + K1C ( +/- 277g of material)

The dimensions of the hexagons match those on the back of the printer.

All previously designed accessories can be used with this wall.

The right side wall comes in two models:

1st - Same as the left side.

2nd - Includes support for the spool and sensor.

The central cover can be customized (STEP file included).

The pieces are attached to the printer with M3x8mm screws (see image).

All pieces are numbered on the longest side (see image).

Installation is done in numerical order for each piece.

The first piece to be installed is the bottom left piece.

Do not fully tighten the screws until all pieces are installed and pre-screwed.

The screws removed from the printer can be used to secure the pieces together.

/////BOM to print LEFT SIDE

1 x LEFT_HONEYCOMB_1

1 x LEFT_HONEYCOMB_2

1 x LEFT_HONEYCOMB_3

1 x LEFT_HONEYCOMB_4

1 x COVER_1 (customizable)

2 x COVER_2

/////BOM to print RIGHT SIDE

1 x RIGHT_HONEYCOMB_1

1 x RIGHT_HONEYCOMB_2

1 x RIGHT_HONEYCOMB_3

1 x RIGHT_HONEYCOMB_4

1 x COVER_1 (customizable)

2 x COVER_2

/////BOM to print RIGHT SIDE wiht SPOOL and SENSOR

1 x RIGHT_HONEYCOMB_1_SPOOL

1 x RIGHT_HONEYCOMB_2_SPOOL

1 x RIGHT_HONEYCOMB_3_SPOOL

1 x RIGHT_HONEYCOMB_4_SPOOL

1 x HOLDER

1 x COVER_1 (customizable)

2 x COVER_2

/////ACCESSORIES FOR THESE PANELS by @stoffies00711

If you’re printing this project, you might want to take a look at some accessories made by @stoffies00711 that work with these panels.

I’m leaving the link here in case you want to check them out.

https://www.crealitycloud.com/model-detail/ptfe-tube-clips-k1c-rear-panel?source=61

https://www.crealitycloud.com/model-detail/gluestick-cutter-holder-creality-k1-rear-panels?source=61

/////ATTENTION - PDF GUIDE AVAILABLE

- If you use the version with the sensor repositioning, you need to INSTALL [4x] M3 D5 L5mm INSERTS ON WALL 2 on the RIGHT side.

- Make sure the bolts aren't too long. They shouldn't go past the frame's thickness to avoid damaging any internal components.

- The project parts should be PRINTED in ABS or similar materials due to their resistance to high temperatures, ensuring durability and reliability.

- THIS PROJECT IS DESIGNED TO WORK WITH THE PRINTER'S SIDE PANELS

CREALITY K1|K1C|K1SE - HONEYCOMB STANDARD TOOL WALL

0.2mm layer, 3 walls, 15% infill