Double Hook — Heavy-Duty Cable & Hose Wall Mount (V4)

Boost Me

Feel free to boost if you enjoy! :)

Boost

Short Description
A strong double-cradle wall hook designed for organizing extension cords, EV/lawn cables, air hoses, garden hoses, shop-vac hoses, ropes and workshop accessories. The V4 design uses two wide saddle-style cradles, reinforced side geometry and support-free FDM printability for a clean, practical and durable garage storage solution.

Full Description
Double Wall Hook V4 – Heavy-Duty Cable, Hose & Extension Cord Organizer

The V4 Double Wall Hook is a heavy-duty storage solution designed to keep cables, hoses and workshop accessories neatly organized and off the floor. It is ideal for garages, workshops, utility rooms, sheds, 3D printing rooms, garden storage areas and general DIY workspaces.

This version uses a dual-cradle saddle design instead of a single narrow hook. The two curved supports help distribute the load across a wider area, which is especially useful for coiled extension cords, air hoses, water hoses, EV/lawn equipment cables, shop-vac hoses, rope and other flexible items that can kink or deform when stored on a sharp hook.

The V4 geometry is designed around practical strength and efficient printing. The reinforced frame, open cutouts, rounded transitions and thick front lips create a strong hook while keeping material use and print time reasonable. The design also includes two screw mounting points for a more stable wall-mounted installation compared to a single-screw hook.

This model is built for support-free FDM printing in the recommended orientation, making it easier to print, easier to clean up and more reliable for everyday workshop use.

Key Features

Heavy-duty double wall hook for garage and workshop organization
Dual saddle-style cradle geometry for better cable and hose support
Helps reduce sharp bending points and keeps coils sitting naturally
Reinforced V4 frame with strong side supports and rounded stress-relief areas
Two screw mounting points for stable wall installation
Raised front lips help prevent cables, hoses and ropes from sliding off
Designed to print without supports in the recommended orientation
Suitable for PETG, ABS, ASA, Nylon and reinforced filaments
Great for extension cords, garden hoses, air hoses, shop-vac hoses and rope
Practical functional print for clean cable management and storage

Practical Use Cases
Use this double wall hook for:

Extension cords
EV charging cables
Lawn equipment cables
Air compressor hoses
Water hoses
Garden hoses
Pressure washer hoses
Shop-vac hoses
Vacuum hoses
Coiled ropes
Dog leashes
Tie-down straps
Small welder leads
Marine/RV lines and hoses
General workshop and garage storage

Why V4?
The V4 version is designed for users who need more support than a standard single wall hook. The double-cradle layout gives the stored item two support points, which helps the cable or hose sit more evenly and securely. This makes the hook especially useful for heavier or bulkier coils.

Compared to a simple hook, the V4 design offers:

Wider support area
Better coil stability
Two mounting screws
More balanced load distribution
Stronger reinforced frame
Cleaner workshop appearance
More secure storage for larger cable and hose bundles

Recommended Print Settings
Printer type: FDM / FFF
Nozzle: 0.4 mm recommended
Optional nozzle: 0.6 mm for faster and stronger prints
Layer height: 0.20–0.28 mm
Walls / perimeters: 5–6
Wall thickness target: approx. 2.0–2.4 mm
Top/bottom layers: 6–8
Infill: 45–60%
Recommended infill: Gyroid, Cubic or Tri-Hex
Supports: No
Brim: Optional, 5–8 mm if bed adhesion is weak
Print orientation: Mounting face on the bed, hooks pointing upward
Material recommendation: PETG for general use
Stronger options: ABS, ASA, Nylon, PA-CF or other reinforced filaments

Material Guide
PETG is recommended for most users because it offers a good balance of strength, toughness and temperature resistance. It is a strong choice for garage, workshop and utility room use.

PLA can be used for lighter indoor storage, but it is not recommended for heavy loads, warm environments or long-term stress.

ABS or ASA are suitable for more demanding environments, especially where heat resistance or outdoor durability is important.

Nylon / PA-CF can be used for maximum strength if your printer and slicer profile are properly tuned.

PETG Starting Profile
These are general starting values and may need adjustment depending on your filament and printer:

Nozzle temperature: 230–245 °C
Bed temperature: 75–85 °C
Cooling: 30–60% after the first layers
Speed: Moderate speed recommended for better layer adhesion
Bed adhesion: Brim recommended if corners lift
Dry filament: Strongly recommended for best strength and surface finish

Mounting Instructions
Choose a strong mounting surface such as a wall stud, wood panel, plywood board, cabinet side or solid workshop wall.
Hold the hook in position and mark the screw holes.
Pre-drill if mounting into wood or cabinet material.
Use suitable screws and anchors for your wall type.
Tighten the screws until the heads sit flush in the countersinks.
Do not overtighten, as this may damage the printed part.
Test the hook with a light load first.
Increase load gradually before daily use.

Load Capacity Note
The real load capacity depends on material, print quality, layer adhesion, wall count, infill, screw type and mounting surface.

With strong material such as PETG, ABS, ASA or Nylon, high wall count and a solid mounting surface, this hook is intended for practical cable and hose storage. However, every setup is different. Always test gradually and use at your own risk.

Avoid using brittle materials or weak wall anchors for heavy loads.

Highlights

Dual cradle geometry: two semicircular saddles share the load and prevent tight bends in cables/hoses.

Triangulated, ribbed body: high strength-to-weight with stress-relief fillets in all hot spots.

Countersunk wall holes (x2): sized for common 4–5 mm wood/sheet-metal screws (use anchors in masonry/drywall).

Finger-safe tip & stop tabs: rounded hook nose and raised lips help keep coils from sliding off.

Prints without supports in the recommended orientation.

Scale-friendly: uniform scaling ±5–10% adapts to your bundle diameter without breaking fit.

Typical use cases

230 V extension cords, fast-charger leads, compressor lines, garden hose, pressure-washer hose.

Coiled ropes, vacuum hoses, small welder leads, dog leashes, and general garage storage.

Marine/RV: mooring lines and bilge hoses (use PETG or ASA for moisture/UV).

Indicative capacity: With PETG or ABS/ASA, 6 walls, ~55–60% gyroid infill, mounted into a stud or solid anchor, one hook typically handles ~8–12 kg static load. Real results depend on material, slicer, printer, and wall/fasteners. Always test gradually and use at your own risk.

Dimensions & fit (reference)

Cradle inner radius: ~30–35 mm per saddle — ideal for bundled diameters Ø20–60 mm.

Depth from wall: ~70–85 mm.

Overall width: ~80–95 mm.

Countersinks: through-holes for Ø4.0–5.0 mm screws, head Ø up to ~9 mm.

Footprint: broad, flat mounting face for solid wall contact.

(Minor variation may occur with slicer and scaling.)

Recommended print settings (FDM)

Nozzle: 0.4 mm (0.6 mm for faster/stronger parts)

Layer height: 0.20–0.28 mm

Walls/Perimeters: 5–6 (≥2.0–2.4 mm wall thickness)

Top/Bottom: 6–8 layers (≥1.2–1.6 mm)

Infill: 45–60% gyroid (cubic/tri-hex also fine)

Material: PETG (general), ABS/ASA (heat/UV), Nylon/PA-CF (max strength)

PETG temps (guide): Nozzle 235 °C, Bed 80 °C

Cooling: 30–60% (low for first layers)

Adhesion: 5–8 mm brim if needed

Supports: None (standard orientation)

Orientation: Mounting face on the bed, hooks pointing up — aligns filament strands with load and strengthens the nose.

Filament note: Avoid brittle PLA where heat or heavy load is expected.

Mounting

Position over a stud or use suitable anchors for your wall type.

Mark holes and pre-drill:

Wood: 3.0–3.5 mm pilot for 4–5 mm screws.

Masonry/brick: 6–8 mm plug + matching screw.

Drywall: metal toggle or rated drywall anchors.

Drive screws until the heads sit flush in the countersinks—don’t overtighten.

Test-load gradually before daily use

Double Heavy Duty Hook / Tool Holder — Cable Organizer (V4)

Creatility-HI-0.4 mm Nozzle 15% infill

Creatility-HI-0.4 mm Nozzle 60% infill

0.2mm layer, 2 walls, 15% infill