Ever since I got my Snapmaker U1 delivered, I have wanted to print the four-colour Majora's Mask model. However, I wasn't quite happy with the painting or the high wall thickness (a remnant of the model being intended as a keychain). One thing led to another, and I ended up spending a month adjusting the 3D model in Blender and painting the model by hand in OrcaSlicer.

The model is printed on five plates and needs to be glued together afterwards. I tried my best to make assembly as easy as possible. If you don't count waiting for the glue to dry, it took me about 30 minutes to assemble everything.

You can find more detailed information and an assembly guide further down in the description. Happy printing!

Features

4-Color CFSC ompatible: Optimized for single CFS/AMS or toolchangers like the U1.
Higher Detail: Added extra geometry for colored lines (white, black, etc.) for sharper visuals.
Slimmer Design: Reduced wall thickness by 50% to save material and to better match the scale.

Easier Assembly:
- Notches on most interfaces for precise alignment.
- Pegs for secure gluing of the two main halves.
Wall-Mount Ready: Hidden wall holder geometry and a matching wall mount (invisible from the front).
Repainted: Entire model repainted due to geometry changes. This took a long time.

Filament required

Creality K2 CFS (depends on your flush volumes, used default 1.3 multiplier)

Black: 1300g
Yellow: 630g
Red: 710g
Purple: 280g
Orange: 470g
White: 400g
Light Green: 130g
Light Blue: 70g
Tan: 105g

Total Filament: 4095g (~4kg)Total Time: 9d10h (226h)

Snapmaker U1 (Toolchanger)

Black: 790g
Yellow: 200g
Red: 170g
Purple: 150g
Orange: 100g
White: 65g
Light Green: 30g
Light Blue: 25g
Tan: 25g

Total Filament: 1555gTotal Time: 3d 1h (73h

Printing

Use the provided .3mf (print profile) as only it has the paint information. In the .3mf there is a fully assembled 3d model outside of any plate. It is there as a reference, don't use it to print! I used it to start painting, but it is missing some painting that i could only add after copying and splitting it apart.

The wall holder is an additional part, that is precisely aligned with the mask halves.

There is a .3mf file for CrealitySlicer, Snapmaker Orca and for BambuStudio availabe.

Assembly

See the provided PDF under "Instruction Files" for a more compact Assembly Guide!

Step 1

Print out each plate and assemble all the parts as shown in the picture below.
If there is any stringing, use a lighter or heat gun to remove it.
Have superglue on hand.

Step 2

Press the pupil into the eye. No glue is required.
Test the fit of the eyes to ensure you have the correct side and orientation.
Apply superglue to the socket and press the eye into it.Repeat for the other side.

Step 3

Make sure you have all the yellow triangles and that they are in the correct sockets.
Push the triangles into their sockets. No glue is required.

Step 4

Place the mask half onto its side.
Glue the upper horn (tan colour) into place.
Glue the green horn into place.
Glue the red horn into place.
Finally, glue the orange and blue horns into their respective places.
Repeat for the other side.

Step 5

Let the halves sit for a while to let the glue dry.

Step 6

Place the mask halves on their backs.
Add glue to all ten peg indents on one half.
Insert all the pegs into their indents.
Add glue to all ten peg indents on the other half.
Add glue to the entire interface of the other half.
Align the two halves using the pegs and press them together.

Result

Boost Me

If you've enjoyed this project, please boost this model. It means a lot! :)

Boost

Attribution

Uses origina lwood grain model as starting point
https://www.***********.com/thing:686111
Inspired by the MakerWorld 4-color AMS model.
https://**********.com/en/models/1608329-multicolor-majora-s-mask-single-ams-version

4-Color CFS Majora’s Mask: High Detail, Easy Build

0.2mm layer, 2 walls, 15% infill

Original