I wanted to thank @SteveHanov - this is his brilliant idea for calibrating prints, I just tweaked it a bit....

I've corrected a miscalculation and adapted the calibration model to a 5mm diameter drill bit - it's more accurate than a screw head.

***********************************************************************************************

What to do with this model?

This is a model for calibrating prints from a specific filament (or rather for calibrating silcer settings) - it is not a printer calibration.

In other words, if you need a functional print where dimensional accuracy to the model is important, then this calibration is for you.

This calibration allows you to calculate:

- the shrinkage value of the felt,

- x-y correction,

- hole correction.

Personally, I use Oracaslicer (Creality Print/BambuStudio has the same parameters available) there all three values are included in the parameters:

The shrinkage value in the parameters of the filament.

The x-y correction and hole correction in the print parameters.

-----------------------------------------------------------------------------------------------------------

On the model, the -4 and +4 mark the values of the extreme holes:

-4 o means 4.6 mm (i.e. -0.4 mm from the diameter of the reference hole)

+4 means 5.4 mm (i.e. +0.4 mm from the reference hole diameter)

So:

- if the drill enters the holes in the +4 direction when measuring - the values are subtracted.

- if the drill enters the holes in the -4 direction when measuring - the values are added.

----------------------------------------------------------------------------------------------------------

How it works:

1. Print the model.

2. Open link with calculations for our model:

https://www.wolframalpha.com/input?i=systems+of+equations+calculator&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation1%22%7D+-%3E%22100a+-+2b+%3D+99.32%22&assumption=%22FSelect%22+-%3E+%7B%7B%22SolveSystemOf3EquationsCalculator%22%7D%2C+%22dflt%22%7D&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation2%22%7D+-%3E%2210a+-+2b%3D9.88%22&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation3%22%7D+-%3E%225%2Fa+-+2c+%3D+4.9%22

Calculations link address:

https://www.wolframalpha.com/input?i=systems+of+equations+calculator&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation1%22%7D+-%3E%22100a+-+2b+%3D+99.32%22&assumption=%22FSelect%22+-%3E+%7B%7B%22SolveSystemOf3EquationsCalculator%22%7D%2C+%22dflt%22%7D&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation2%22%7D+-%3E%2210a+-+2b%3D9.88%22&assumption=%7B%22F%22%2C+%22SolveSystemOf3EquationsCalculator%22%2C+%22equation3%22%7D+-%3E%225%2Fa+-+2c+%3D+4.9%22

3. Measure the longer side and enter the result in the calculation area: ‘99.32’.

4. Measure the shorter side and enter the result in the calculation area: ‘9.88’.

5. Insert the 5mm drill bit into the smallest hole it will fit into:

The middle hole is the reference hole and is assumed to be the zero hole.

Example1 ===

For example, if you place a 5mm drill three holes higher than the center hole (in the +4 direction), enter a value of 4.7 in the "4.9" calculation point.

The holes differ by 0.1 mm, so the reference hole is 4.7 mm because you only put the drill into the third hole.

Drill+0.3mm=5mm

Drill=5-0.3=4.7

Example2 ===

For example, if you put the drill into 1 hole above the reference hole, you should enter in

4.9 in the place of ‘4.9’.

Drill+0.1mm=5mm

Drill=5-0.1=4.9

Example3 ===

For example, if the drill has already entered the second hole, but in a direction of -4 from the centre hole, a value of 5.2 should be entered into the calculation instead of "4.9".

Drill-0.2mm=5mm

Drill=5+0.2=5.2

6. Once the measured values have been entered:

1) Switch on "Compute".

2) Then "Approximate form".

We have now received the results in a form that we can already enter in Creality Print.

7. After the measurements and calculations, the results for the values a, b, c are entered in CrealityPrint/Orcaslicer/BambuStudio respectively:

- the shrinkage (XY) value of the filament - the ‘a’ value of the calculation results multiplied by 100.

For example if a≈0.993778 then the shrinkage value will be: 99,3778 %

- x-y correction - value ‘b’ of the calculation results.

- hole correction - value ‘c’ of the calculation results.

In other slicers these parameters may be described differently in not all may be hole correction.

8. Having entered the above parameters into CrealityPrint/Orcaslicer/BambuStudio for our filament, we can print the calibration model again.

A well calibrated model should be 100x10x5mm and the 5mm drill should fit tightly into the centre hole.

CONCLUSION

💚💚💚If you enjoyed the project please like it.💚💚💚

Post your makes and let me know how it works out for you.

If anyone has any comments about them - I'd be happy to listen and improve the models.

☕☕☕

Did my project bring you joy, save you time or solve your problem? Share it with me and make me happy - buy me ko-fi:

https://ko-fi.com/mario_l

☕☕☕

Calibration CrealityPrint/OrcaSlicer/BambuSt print profile

0.2mm layer, 2 walls, 15% infill

Original