The two parts made with Creality Hyper PLA ( Black + White )

If you use not fast print compatible material,then set lower speed values.

Global settings:

Nozzle temp : 220°C

BedTemp : 60°C

Parameters for the "main body" :

Layer Height and Line Width:

Layer Height: 0.2 mm

Initial Layer Height: 0.2 mm

Default Printed Line Width: 0.42 mm

Initial Layer Line Width: 0.55 mm

Outer Wall Line Width: 0.42 mm

Inner Wall Line Width: 0.45 mm

Top Surface Line Width: 0.42 mm

Infill Line Width: 0.45 mm

Inner Solid Infill Line Width: 0.42 mm

Support Line Width: 0.42 mm

Seam Settings

Seam Position: Aligned

Segmented Inner Seams: Disabled

Seam Gap: 10%

Travel Seam: Nowhere

Wiping Speed: 80 mm/s

Walls and Shells

Number of Walls: 4

Alternative Extra Wall: Not Enabled

Top/Bottom Shells:

Top Surface Pattern: Monotonic

Top Layers: 4

Top Layer Thickness: 0.8 mm

Bottom Surface Pattern: Monotonic

Bottom Layers: 3

Bottom Layer Thickness: 0.6 mm

Top/Bottom Solid Fill Transition: 25%

Infill:

Infill Density: 13%

Infill Pattern: Lines

Short Infill Anchor Length: 400%

Inner Solid Infill Pattern: Monotonic

Fill Gaps: Everywhere

Speed Settings:

Initial Layer Speed: 60 mm/s

Initial Layer Infill Speed: 105 mm/s

Initial Layer Flow Compensation: 100%

Slw Layers Count: 4

Other Layer Speeds:

Outer Wall Speed: 200 mm/s

Inner Wall Speed: 300 mm/s

Small Perimeters Speed: 50%

Infill Speed: 250 mm/s

Inner Solid Infill Speed: 250 mm/s

Top Surface Speed: 200 mm/s

Gap Fill Speed: 250 mm/s

Overspeed Compensation: Enabled

Support Settings:

Supports Enabled: Yes

Support Type: Tree (auto)

Support Style: Default

Support Overhang Angle Threshold: 30°

First Layer Density: 90%

First Layer Expansion: 2 mm

Supports Only from Build Plate: No

Supports Only for Critical Areas: No

Remove Small Overhangs: No

Movement and Acceleration

Travel Speed: 500 mm/s

Acceleration:

Normal Printing Acceleration: 12000 mm/s²

Outer Wall Acceleration: 5000 mm/s²

Inner Wall Acceleration: 5000 mm/s²

Bridging Acceleration: 50%

Infill Acceleration: 100%

Inner Solid Infill Acceleration: 100%

Initial Layer Acceleration: 2000 mm/s²

Top Surface Acceleration: 2000 mm/s²

Movement Acceleration: 10000 mm/s²

Enable Accel-to-Decel Transition: Yes

Accel-to-Decel Ratio: 25%

Jerk (XY Direction):

Default Jerk: 12 mm/s

Outer Wall Jerk: 8 mm/s

Printing settings for the "logo body":

Layer Height and Line Width

Layer Height: same (0.2 mm)

Initial Layer Height: same (0.2 mm)

Default Printed Line Width: same (0.42 mm)

Initial Layer Line Width: same (0.55 mm)

Outer Wall Line Width: same (0.42 mm)

Inner Wall Line Width: same (0.45 mm)

Top Surface Line Width: same (0.42 mm)

Infill Line Width: same (0.45 mm)

Inner Solid Infill Line Width: same (0.42 mm)

Support Line Width: same (0.42 mm)

Seam Settings

Seam Position: same (Aligned)

Segmented Inner Seams: same (Disabled)

Seam Gap: same (10%)

Travel Seam: same (Nowhere)

Wiping Speed: same (80 mm/s)

Walls and Shells

Number of Walls: same (4)

Alternative Extra Wall: same (Not Enabled)

Top/Bottom Shells:

Top Surface Pattern: same (Monotonic)

Top Layers: same (4)

Top Layer Thickness: same (0.8 mm)

Bottom Surface Pattern: same (Monotonic)

Bottom Layers: updated (previously 3, now 0)

Bottom Layer Thickness: updated (previously 0.6 mm, now 0 mm)

Top/Bottom Solid Fill Transition: same (25%)

Infill

Infill Density: same (13%)

Infill Pattern: same (Lines)

Short Infill Anchor Length: same (400%)

Maximum Infill Bridge Length: same (20 mm)

Inner Solid Infill Pattern: same (Monotonic)

Fill Gaps: same (Everywhere)

Speed Settings

Initial Layer Speed: same (60 mm/s)

Initial Layer Infill Speed: same (105 mm/s)

Initial Layer Flow Compensation: same (100%)

Slow Layers Count: same (4)

Other Layer Speeds:

Outer Wall Speed: same (200 mm/s)

Inner Wall Speed: same (300 mm/s)

Small Perimeters Speed: same (50%)

Infill Speed: same (250 mm/s)

Inner Solid Infill Speed: same (250 mm/s)

Top Surface Speed: same (200 mm/s)

Gap Fill Speed: same (250 mm/s)

Overspeed Compensation: same (Enabled)

Movement and Acceleration

Travel Speed: same (500 mm/s)

Acceleration:

Normal Printing Acceleration: same (12000 mm/s²)

Outer Wall Acceleration: same (5000 mm/s²)

Inner Wall Acceleration: same (5000 mm/s²)

Bridging Acceleration: same (50%)

Infill Acceleration: same (100%)

Inner Solid Infill Acceleration: same (100%)

Initial Layer Acceleration: same (2000 mm/s²)

Top Surface Acceleration: same (2000 mm/s²)

Movement Acceleration: same (10000 mm/s²)

Enable Accel-to-Decel Transition: same (Yes)

Accel-to-Decel Ratio: same (25%)

Jerk (XY Direction):

Default Jerk: same (12 mm/s)

Outer Wall Jerk: same (8 mm/s)

PARKSIDE Tool Holder | Wall Mounted

0.2mm layer, 4 walls, 13% infill

0.2mm layer, 3 walls, 15% infill

0.2mm layer, 2 walls, 15% infill