If you know anything about 3D printing, you probably know PLA, the most popular 3D printing filament out there. PLA is known for its ease of use, but sometimes, certain printing issues can make achieving great prints a struggle.

Challenges surrounding the first layer can be especially taxing, as a good first layer is key to a successful print. In order for successive layers to be properly printed, the first layer needs to stick to your printer’s build surface, which is known as bed adhesion in the 3D printing world.

This common problem can be annoying, but it’s also easy to fix. In this article, we’ll go over a few different ways to make your first layer of PLA stick to the bed. These solutions, however, aren’t totally exclusive to PLA, so feel free to use them with other filaments.

Solution #1: Level the Bed

As for most 3D printing problems, leveling the bed should be your first go-to solution. Bed leveling is the process by which you adjust points on your build surface so that they are flat and level. An unlevel bed can cause filament to stick in one area but not others.

There are two main ways to achieve a level bed: manual leveling and automatic leveling. Manual leveling involves using adjustable tools (usually bed knobs) to ensure your bed surface is even and level. To manually level your bed, bring your nozzle to its home position and use the adjustable leveling features to ensure your nozzle is the same height above the bed at all points.

Automatic leveling, on the other hand, involves a sensor or an endstop of some sort that calculates compensation values for printing so the nozzle is equidistant from the bed in every area. It’s very easy to automatically level your bed: Just run a bed leveling sequence. If you use an auto-bed leveling sensor, make sure you set a correct Z-offset, which we’ll get into in the next section.

Solution #2: Change the Z-Offset

Even if you have a level bed or a set of compensation values from an automatic bed leveling sensor, a bad Z-offset can cause poor bed adhesion. If you’re unfamiliar with the term, Z-offset is the distance between the nozzle and the home position of the Z-axis. A poor, unturned Z-offset will cause the nozzle to be either too far above the bed or too close, both of which will negatively impact how the PLA is extruded and which can potentially damage your bed.

To find a functional Z-offset for good bed adhesion, you have to adjust the Z-offset value and test it. While the testing process can be repetitive, it’s worth the effort.

Solution #3: Clean the Bed

A dirty bed can cause poor first layer adhesion because substances on the bed can make the surface uneven. While it may not be visually obvious, oftentimes oils from your hands, dust, dirt, grime, and more can remain on your print bed. If you’re using an adhesive like glue or painter’s tape, leftover residue or an uneven or damaged tape strip can also be problematic.

Cleaning the bed is easy, and all it requires is using a damp cloth (water) to wipe the bed. Just make sure to dry the print surface afterward because water may also limit bed adhesion. If any residue is still stuck, you may want to try using acetone or an unscented IPA in a concentration of over 70%.

Solution #4: Use a Bed Adhesive

If you’re not already doing so, you may want to try using an adhesive substance on your build plate to enhance bed adhesion. Bed adhesives can be vital in laying down a good first layer. Specifically, they allow the melted filament to stick to the surface better and stay down throughout the print.

There are many options for bed adhesives, from sheets that cover large portions of the print bed, like Kapton or painter’s tape, to DIY options like glue or hairspray. You can also use advanced, purchasable special adhesives, including 3D Gloop! or Magigoo.

When applying an adhesive to your print bed, be sure to use just a thin layer over the build plate if it’s one that can be applied (like hairspray or glue). For adhesives, remember that more is not merrier; too much adhesive can worsen problems if leftover residue remains on the bed after a print.

Solution #5: Adjust Slicer Settings

After addressing the mechanical issues, the slicer should be the next place you turn to. A few different slicer settings can affect bed adhesion for the first layer: bed temperature, first layer printing speeds, and adhesion assistants like a brim or a raft.

When adjusting your slicer settings, try not to change more than one setting at a time, otherwise it’s hard to identify which setting fixed your problem.

Bed Temperature
Temperature can be instrumental for good bed adhesion, so first, try raising your bed temperature in increments of 5 °C. For PLA, start at 55 °C, and as needed, raise the temperature incrementally up to 70 °C. Make sure, however, not to set the bed temperature too high because this can cause difficulty with removing parts.

If you don’t see better results after setting the bed temperature to 70 °C, your solution probably lies in other settings.

Print Speed
The next setting you should change is print speed. The base speed setting isn’t important for first layer adhesion, so focus on the first or initial layer print speed setting. To start, set your first layer speed to 25 mm/s, and as needed, go down in increments of 5 mm/s from there.

Brim & Raft Settings
Another setting you may want to change to improve the first layer is an adhesion assistant such as a brim or a raft. Some slicer settings default to using a skirt, which is helpful to detect issues prior to beginning a print. A skirt, however, doesn’t support bed adhesion for the print itself; a brim or a raft would be a better choice.

A brim is a perimeter that goes around and attaches to the print, and a raft is an entire base structure that’s printed before and right under your print. A raft consumes a fair amount of material, especially if your print is large. For this reason, we recommend starting with a brim and then trying a raft if that doesn’t work.

Solution #6: Change the Build Plate

As a last resort, you may want to swap out your build plate. That’s because some build plates, especially cheaper ones, fail as they can warp and have permanent bends in certain areas over time. Warped or damaged beds are hard to level, so bed adhesion can be a problem; getting a new build plate made of premium material can help you achieve good bed adhesion.

There are many options for the material of a print bed. For example, you can get build plates made of steel, glass, polypropylene, among many other materials. For glass, you have a range of different types including borosilicate glassand even ceramic glass.

In addition to the material used, you can also get beds with special features or abilities. For example, there’s a wide range of flexible and magnetic build plates available, not to mention smooth beds and textured beds.

There isn’t one single best type of build plate because each bed is good for different things. However, for PLA, tempered glass and smooth spring steel build plates are both magnificent options with good performance.

Retrieved from: https://all3dp.com/2/pla-not-sticking-to-print-bed-build-plate-easy-fixes/

By: Jackson O'Connell

PLA Not Sticking to Bed: 6 Simple Solutions