The "Keeps Your Hands Busy" Fidget Octagon ⯃

A fidget toy for your desk. It sits flat as an eight-sided plate, and every way you move the stem gives it a different look.

🟩 𝗪𝗔𝗬𝗦 𝗧𝗢 𝗣𝗟𝗔𝗬

▸ 𝗧𝘄𝗶𝘀𝘁 𝘁𝗵𝗲 𝗦𝘁𝗲𝗺 — Leave it flat on the desk and twist. The 23 rings sweep around into a pinwheel, each one turning until its corners meet the ring outside it.

▸ 𝗣𝘂𝘀𝗵 𝗮𝗻𝗱 𝗣𝘂𝗹𝗹 — Slide the stem from side to side and the rings shift off-center for a whole different set of visuals.

▸ 𝗟𝗶𝗳𝘁 𝗜𝘁 𝗨𝗽 — Raise it by the stem and the rings step down into a pyramid.

▸ 𝗛𝗲𝗮𝗿 𝗜𝘁 𝗦𝗲𝘁𝘁𝗹𝗲 — Raise and lower it on the desk and it makes a satisfying sound as the rings come back down.

▸ 𝗧𝗲𝘅𝘁𝘂𝗿𝗲𝗱 𝗦𝘁𝗲𝗺 — The stem is textured, so it has a tactile feel under your fingers while you fidget.

🟩 𝗪𝗛𝗔𝗧 𝗠𝗔𝗞𝗘𝗦 𝗜𝗧 𝗪𝗢𝗥𝗞

▸ 𝗣𝗿𝗶𝗻𝘁𝘀 𝗶𝗻 𝗣𝗹𝗮𝗰𝗲 — One print, no assembly. All 23 rings and the stem come off the plate already captured inside each other.

▸ 𝗧𝘂𝗻𝗲𝗱 𝗚𝗮𝗽𝘀 — The gap between rings widens from about 0.8mm at the stem to about 1.4mm at the rim, so the outer rings keep turning freely instead of binding up.

▸ 𝗧𝗲𝘀𝘁𝗲𝗱, 𝗡𝗼𝘁 𝗝𝘂𝘀𝘁 𝗠𝗼𝗱𝗲𝗹𝗲𝗱 — This is the shape the whole set was tuned against. Every ring turns, and the stack stays together through a full twist.

▸ 𝗢𝗻𝗲 𝗖𝗼𝗹𝗼𝗿, 𝗡𝗼 𝗦𝘄𝗮𝗽𝘀 — A single spool, no filament changes, no purge and no prime tower.

🟩 𝗖𝗛𝗘𝗖𝗞 𝗬𝗢𝗨𝗥 𝗕𝗘𝗗 𝗙𝗜𝗥𝗦𝗧

▸ 163 x 163mm and 39mm tall with the stem. It needs a 180mm bed.

🟩 𝗣𝗥𝗜𝗡𝗧 𝗦𝗘𝗧𝗧𝗜𝗡𝗚𝗦

No supports required · no brim · 0.20mm layer height · 2 walls · 10% grid infill · PLA

Printed on a Creality Hi 2 in 3h 22m and 101g. Happy fidgeting! ⯃

Boost Me

If you like this model, please boost!

Boost

Fidget Octagon

MakerX

Tetapan Cetak(1)

0.2mm layer, 2 walls, 10% infill

Penerangan

Lesen

Model Berkaitan